What makes a dryer stop getting hot

Failure to investigate and address why the thermal fuse was tripped is not only likely to result in more blown thermal fuses but means your dryer will remain a potential fire hazard. If your thermal fuse was responsible for the issue, your first course of action after replacing it should be to check your dryer vent.

The flexible metal hose that attaches your dryer to the vent in your home can become blocked with a buildup of lint.

As this blocks the proper release of hot, wet air from your dryer drum, it can cause the dryer to heat up. If the hose is blocked up, even partially, this is likely what caused the thermal fuse to blow. It will need to be cleaned out and you should monitor your dryer just in case this was not the sole cause, but a contributing one. You will also want to see if the clog goes beyond the flexible tubing. If there is a lint clog in the actual ventilation system of your home, depending on how deep it is, you may need a professional with the proper tools to come out and remove it.

Almost all the horror stories of dryer fires are caused by lint blockages in the ventilation, so it is important to never ignore this issue and fix it quickly before further use. The thermostat and temperature switch is responsible for keeping an even temperature inside your dryer. If you had a blown thermal fuse and you are investigating as to why these two parts should be looked into. While faults in either of these parts can result in no heat in your dryer, it is more likely that they will result in the heat not being shut off during the dryer cycle.

This means that your clothing will get too hot and it will ultimately trip the thermal fuse. Both the thermostat and the temperature switch can be tested with a multimeter. If the thermostat is not working properly, you should get a zero reading. However, for the temperature switch, it will either read zero or infinity. If it is working properly, once you turn the switch the reading should change to either zero or infinity, opposite your initial reading.

If it does not switch, then it is the faulty part. While replacing a temperature switch is as easy as removing it and connecting the new one, replacing a bad thermostat is a little more involved.

There are more wires to disconnect and it is crucial to remember to replace the in the right order. On some models, you may also need to pull the thermostat out in order to replace it. It's not as bad as it may seem either.

This should be done every six months to a year to not only keep your dryer running smoothly and efficiently, but also to prevent or reduce the risk of fire. It's a different story altogether when the dryer just won't get hot at all. Even when set to high heat, the clothes remain wet and cold.

A blown thermal fuse may be to blame. On newer dryers, a blown thermal fuse may prevent the dryer from running at all. This fuse is put in place to help prevent fires. Fuses can simply wear out on their own, but they're designed to short at higher-than-normal temperatures, which could be caused by a number of things.

Look out for clogged ventilation, a clogged lint screen or an overloaded machine. To fix a blown fuse, you must replace it. To do that, you must first locate it. It should be located near the exhaust duct, so you'll need to disconnect the power and remove the back panel.

Unscrew the fuse and replace it with a new one. You should be able to find a replacement fuse at your local hardware store or online. Again, the easiest way to find one is to Google your dryer's model number. If you start a cycle and hear the motor hum but the drum remains still, you've got a serious problem. Fortunately, it could also be one of the easiest to fix. Belts wear out. It's a fact of life, and your dryer's belt is no exception.

If your dryer turns on but the drum doesn't spin, this should be your first stop on the checklist. Start by unplugging the dryer and removing the rear panel. Reason 1. Reason 2. Reason 3. Heating element issues When a device is new, the heating element responds well to temperature changes, increasing the warm air output as you switch the temperature mode.

Reason 4. Tip 1. Tip 2. Clean the drum of the dryer thoroughly Depending on the frequency of use, you should clean your appliance every couple of uses. Tip 3. Tip 4. Clean the lint screens Lint screens are one of the dryer components ensuring the safety of usage. Tip 5. The FIX Appliances CA team has decades of experience repairing, installing and maintaining all types of appliances — from kitchens to washing machines.

We are licensed to fix, repair, and maintain both electric and gas appliances. That, coupled with a high level of expertise, is why we are the unrivalled repair technician team in the country. And for many manufacturers, for example, to improve the quality of service, we have same-day service availability. For example, this time, we can schedule a selection of appliances from Panasonic or KitchenAid appliance repair on the same day.

Check this option with our dispatchers before noon on the same day. Jobs will be booked on a first-come, first-served basis. We always find time to respond to inquiries and follow-up questions. FIX Appliances CA has a dedicated customer support team ready to answer questions and offer assistance. We offer every homeowner high-quality, affordable repair services. FIX Appliances CA technicians will provide a refund if an appliance we repaired or replaced failed in the 3-month window after the repair.

Discount Coupon Enjoy this special offer for your appliance. Discover how Fix Appliances maintains a 5-star service record since day one. Angela, Kleinburg, ON. Alex, Alliston, ON. Read More Customer Reviews. Homeowner Guide for Appliances.